Cost-effective Solid Polycarbonate Sheet Bulk Production
Product details of the solid polycarbonate sheet
Quick Detail
Mclpanel solid polycarbonate sheet is designed by our independent designers who have been paying great attention to it. Its quality is ensured for a better global competitiveness. solid polycarbonate sheet of Mclpanel has very extensive application in different scenarios. Since its establishment, Shanghai mclpanel New Materials Co., Ltd. has obtained ISO9001 certification.
Product Introduction
Mclpanel adheres to the principle of 'details determine success or failure' and pays great attention to the details of solid polycarbonate sheet.
Product Description
Plug-Pattern Design: The plug-pattern design of these sheets consists of small plugs or protrusions on the surface, which helps to enhance the structural integrity and stability of the sheet.
Four-Wall Rectangle Structure: The four-wall Rectangle structure of these sheets provides increased strength and rigidity compared to standard multi-wall polycarbonate sheets. This makes them more resistant to impacts and bending .
Seamless Glazing Option: Some 4 Walls Plug-Pattern Sheets are produced with a thermoclick system on the side edges, allowing for a seamless glazing option. This makes the installation process easier and provides a visually appealing finish.
Four wall polycarbonate partition panel have emerged as a popular choice for building exteriors and facades due to their exceptional performance and design versatility. These panels offer a range of benefits that make them an attractive option for architects, contractors, and building owners.
product parameters
|
Item |
Thickness |
Width |
Length |
|
Polycarbonate Plug-Pattern Panel |
20/30/40 mm |
500 mm |
5800 mm 11800 mm Customized |
|
Raw Material |
100% virgin Bayer/ Sabic |
||
|
Density |
1.2 g/cm³ |
||
|
Profiles |
4-Wall Rectangle/7-Wall Rectangle/ Diamond Structure |
||
|
Colors |
Transparent, Opal, Green, Blue, Red, Bronze and Customized |
||
|
Warranty |
10 years |
||
Key Characteristics and Advantages of Polycarbonate Facade Panels
product Advantages
Product application
● Facades: The plug-pattern design and enhanced strength of 4 wall
Rectangle polycarbonate partition panel make them suitable for facade applications. They can be used to create visually appealing and durable exterior surfaces for buildings.
● Internal Partitions: Four wall polycarbonate partition panel can be used as partitions to divide interior spaces. They provide privacy while still allowing light to pass through, creating a bright and open atmosphere.
● External Wall Cladding: These sheets can be used as external wall cladding to enhance the aesthetics and durability of buildings. The plug-pattern design adds visual interest to the facade.
Features
● Coefficient of linear expansion: 0.065 MM/M℃
● Fire retardant level: GB8624, B1
● No thermal expansion
● 100% water leakage proof
● High light transmittance
● Can withstand extremely high loads
● Double-sided UV protection
● High thermal insulation performance
● Suitable for bending design
● Intelligent light control system
● Simple and fast installation
STRUCTURE
Four wall rectangular structure, seven wall rectangular structure, seven wall x structure, ten wall structure.
Plug-Pattern Design: The plug-pattern design of these sheets consists of small plugs or protrusions on the surface, which helps to enhance the structural integrity and stability of the sheet.
PLUG-PATTERN PC SHEET INSTALLATION
For minimizing the infltration of dust particles into the chambers of the panels, the panel ends have to be sealed carefulyThe upper panel end and lower end must be tightly sealed with Anti-Dust-Tape. lt is important that tongue and groove jointof the panels are also sealed completely and carefully.
1.For minimizing the infltration of dust particles into the chambers of the panels, the panel ends have to be sealed carefulyThe upper panel end and lower end must be tightly sealed with Anti-Dust-Tape. lt is important that tongue and groove jointof the panels are also sealed completely and carefully
2.The protective film of the panels must be removed in areas of taping. lt must be ensured that remove the protective filmfrom all around about 6cm when the panels are set into the frame profile.
3.There must be an expansion joint of approx. 3-5mm in between(this value is valid for an installation temperature of +20 degree)
4.The fastener must be positioned at the horizontal bar and must be pushed against the panel. The fastener must be fixedwith at least two screws at the crossbar.
5.Depending on panel length,it is necessary to use hammer and softwood to interlock the panels.
6.Take care that the fastenersare positioned exactly inside the notches of the panels.
7.The gasket must be pressed directly tightly onto the front panel so it is put under tension and fixed.Chemical resistance of polvcarbonate against other chemicals used are to be checked by customer on site.
8.PC material isespecially avoided to use.After finish installation, remove the panel's protective foil.
Why choose us?
ABOUT MCLPANEL
Our advantage
FAQ
Company Advantages
Shanghai mclpanel New Materials Co., Ltd. is located in shang hai. As a modern enterprise, our company mainly produces and sells Polycarbonate Solid Sheets,Polycarbanote Hollow Sheets,U-Lock Polycarbonate,plug in polycarbonate sheet,Plastic Processing,Acrylic Plexiglass Sheet. We take 'integrity-based, developing and innovating' as our business philosophy, and 'dedication, passion and pragmatism' as our enterprise spirit. Thus, we wholeheartedly provide high-quality products and services for consumers, and strive to build our company into a well-known company with market competitiveness, brand influence and industry driving force. Our company has professional talents who are in charge of the R&D, production and sales of our products. Mclpanel is rich in industrial experience and is sensitive about customers' needs. We can provide comprehensive and one-stop solutions based on customers' actual situations.
Welcome all customers in need to purchase our products.